With the deepening of the national coal-to-electricity policy, electric heating has become an inevitable choice for many northern regions. At the same time, due to the improvement of living standards, the southern region has gradually accepted electric heating products to improve the comfort of the living environment. Therefore, in the past year, electric floor heating products have been popular in the market, and many brands have been born, which has brought confusion to consumers. As a technological innovator in the field of heating ceramic tiles, Guangdong Fenfang Ceramics Co., Ltd. launched the "Fragrance Graphene Electric Heating" product, which has received widespread attention. In order to allow consumers to buy with confidence and not to be deceived just because the product is cheap, "Fragrant Graphene Electric Heating" has specially written an article to analyze the installation costs of different electric floor heating products to provide a reference for consumers.
Judging from the electric floor heating products currently on the market, they are mainly divided into two types - 1. Single heating film type (without reflective film and heat insulation board), 2. .Integral heating chip (heating film, reflective film and heat insulation board are bonded into a whole). Under normal circumstances, the main process of laying and using single-film heating film electric heating products is as follows:
1) Level and clean the floor.
2) The ground is covered with insulation boards and fixed with glue, and then the reflective film is laid. Insulation boards can prevent problems such as slow heating and low temperature caused by heat loss to the ground, and can achieve the purpose of saving electricity and energy. For small-area installations, insulation boards can be omitted and a 5mm-thick reflective film can be used directly.
3) Laying electric heating film: ① Budget the amount of electric heating film required based on the room area. Calculate the total power of the electric heating film area laid, select a suitable thermostat, arrange the positions of the electric heating film (simply fixed with tape) and the thermostat, and overlap is strictly prohibited; ② Electric heating film wiring: insert the wiring clip into the copper bar and silver paste Use special wiring pliers to tighten the gaps between them. Use the jaw end of the pliers to connect the power cord and the electric heating film, and use high-temperature wire according to the situation; ③ Cut the insulating putty into small sections, and glue and seal the exposed wires at the wiring part and the exposed copper strip cuts at the shearing part. Then cover it with PVC electrical tape and press it firmly to ensureDouble insulated and waterproof. Wire and complete the insulating electric heating film, and simply fix it with ordinary tape; ④ Install the thermostat.
4) Laying of waterproof layer: If installing wooden floors, it is recommended to lay polypropylene cloth, or use plastic film + non-woven fabric together. When laying, they should overlap each other by about 10cm, and the ground should be covered. If you are installing floor tiles, it is recommended to first seal the electric heating film with a special PVC envelope, then lay a layer of waterproof polypropylene cloth, then lay a cement pressure plate or wire mesh (connected to the ground wire), and then lay 2-3cm of dry cement mortar. Laying cement pressure plates or wire mesh mainly protects the electric heating film and prevents tripping caused by sediment moisture.
The process of laying and pasting the integral heating chip is as follows:
1) For those using ceramic tiles (marble, etc.) as the floor, paste the heating chip and ceramic tiles (marble, etc.) together.
For those using wooden floors as the ground, lay the heating core directly on the ground. For places where heating chips are not to be laid, lay insulation boards of equal thickness and then lay a layer of waterproofing. Just cloth.
For the paving of small-sized ceramic tile products such as imitation wood floor tiles, it is recommended to first seal the electric heating film with a special PVC envelope, then lay a layer of waterproof polypropylene cloth, and then pave it Cement pressure plate or wire mesh (connected to the ground wire), and then lay 2-3cm of relatively dry cement mortar to level the entire floor.
2) Lay composite heating tiles (marble, etc.). Use cement mortar to lay directly. Since heating tiles (marble, etc.) do not need to be paved throughout the house, ordinary ceramic tiles (marble, etc.) can be paved directly in the conventional way in places that do not need to be paved.
3) Connect the heating chip and install the switch. Since the integral heating chip is directly connected to a waterproof connector, the male and female plugs are directly connected to ensure waterproofing.
Comparing the installation process of the single heating film type and the integral heating chip, the installation of the integral heating chip is simple, has no technical threshold, and almost does not increase the customer's budget. It is more convenient This type of electric heating product has a low overall cost of use, and each heating chip is individually controlled, so damage to one chip will have little impact on the heating effect. As for single-film heating products, the installation requires a professional team, and the overall installation cost is high. Moreover, when problems occur, the entire column is often not heated, seriously affecting the heating effect.
Therefore, we suggest that when choosing electric heating products, consumers should not only consider the performance and price of the product itself, but also consider the overall cost of installation. After comparing the two , decide which type of electric heating product to choose.
(Enterprise feed)
